ME2202 Engineering Thermodynamics Important Questions
Anna University, Chennai
Department of Mechanical Engineering
ME2202 Engineering Thermodynamics Important Questions
Mechanical Engineering Third Semester Important Questions
Engine rpm = 650,
Load applied = 60 kg at a leverage of 1.2m,
Quantity of water = 200 kg
Duration of test
2. A cylinder contains 0.45 m3 of gas at 1 x 105 N/m2 and 80oC. The gas is compressed to a volume of 0.13 m3, the final pressure being 5 X 105 N/m2 Determine i) The mass of gas ii) The value of index ‘n’ for compression The increase in internal energy of the gas and iv) The heat received or rejected by the gas during compression. Take γ = 1.4 R = 294.2 J/kg K
3. A turbine operates under steady flow condition receives steam at the following state pressure = 1.2Mpa, Temperature =1880C, Enthalpy = 2785 kJ/kg, velocity = 33.3m/sec and elevation = 3m. The steam leaves the turbine at the following state: pressure = 20Kpa, Enthalpy = 2512 kJ/kg, velocity = 100m/sec and elevation = 0m. Heat is lost to the surrounding at the rate of 0.29kJ/sec. If the rate steam flow to the turbine is 0.42kg/sec what is the power output of the turbine in KW
4. Three grams of nitrogen gas at 6atm and 160°c is expanded adiabatically to double its initial volume, then compressed at constant pressure to its initial volume and then compressed again at constant volume to its initial state. Calculate the net work done on the gas. Draw P-V diagram for the process. Specific heat ratio of nitrogen is 1.4.
5. One litre of hydrogen at 273 K is adiabatically compressed to one-half of its initial volume. Find the change in temperature of the gas, if the ratio of two specific heats for hydrogen is 1.4
6. An Engine-working on Otto cycle has a volume of 0.45 m3 , pressure 1 bar and temperature 30o,C at the beginning of compression stroke. At the end of compression stroke, the pressure is 11 bar and 210 KJ of heat is added at constant volume. Determine (i) Pressure, temperature and volumes at salient points in the cycle.' (ii) Efficiency
7. Derive the expression for thermal efficiency of a Carnot cycle with its p-V and Ts Diagram?
8. A Carnot engine takes heat from an infinite reservoir at 5500C and rejects it to a sink 2750C. Half of the work delivered by the engine is used to run generator and the other half is used to run heat pump which takes heat at 2750C and rejects it at 4400C. Express the heat rejected at 4400C by the heat pump as % of heat supplied to the engine at 5500C. If the operation of the generator is 500W, Find the heat rejected/hour by the heat pump at 4400C?
9. Establish the inequality of Clausius and express Entropy change in irreversible process.
10. 1 kg of steam initially dry saturated at 1.1 MPa expands in a cylinder following the law PV113 = C. The pressure at the end of expansion is 0.1 MPa. Determine
(i) The final volume
(ii) Final dryness fraction (hi) Work done
(iv) The change in internal energy
(v) The heat transferred
11. Draw the p-V diagram of pure substance and explain its various regions of the diagram in details?
12. with help of T-s diagram explain the various process of ideal Rankine’s cycle and derive the efficiency in terms of enthalpy?
13. Steam at a pressure of 15 bar and 250°C expands according to the law PV1.25 = C to a pressure of 1.5 bar. Find the final conditions, work done, heat transfer and change in entropy. The mass is 0.8 kg
14. Derive clausius-claperyon equation
15. Deduce the Maxwell relations from thermodynamic property relations?
16. Using Clausius Cleperyon’s equation, Estimate the enthalpy of vaporization at 2200C saturation temperature. Take the following data Ts = 2200C; vg = 0.08603m3/kg; vf =0.00119m3/kg.
17. 2kg of air at 300C, 65% RH is mixed adiabatically with 5kg of air at 200C, 10%RH. Determine final condition of the mixture?
18. Give short notes on following
(a) Specific humidity
(b) Relative humidity
(c) Dew point temperature
(d) Wet bulb depression
19. Air has a dry bulb temperature of 250C and wet bulb temperature of 150C. If
the barometer reads 1bar, Calculate
(a) Vapour pressure
(b) Specific humidity
(c) Saturation ratio
(d) Relative humidity
(e) Dew point temperature
(f) Vapour density
(g) Enthalpy of mixture
Check The Section:
MA 2211 Transforms And Partial Differential Equation Important Questions 2013
ME 2201 Manufacturing Technology – I Important Questions 2013
ME 2202 Engineering Thermodynamics Important Questions 2013
ME 2203 Kinematics of Machinery Important Questions 2013
ME 2204 Fluid Mechanics and Machinery Important Questions 2013
ME 2205 Electrical Drives and Control Important Questions 2013
Incoming Search terms:
MA 2211 Transforms And Partial Differential Equation Syllabus 2013
ME 2201 Manufacturing Technology Syllabus 2013
ME 2202 Engineering Thermodynamics Syllabus 2013
ME 2203 Kinematics of Machinery Syllabus 2013
ME 2204 Fluid Mechanics and Machinery Syllabus 2013
ME 2205 Electrical Drives and Control Syllabus 2013
______________________________________________________________________
All you need to do is ” Follow http://indiaedu9.blogspot.in/ on Social Networking Sites like Facebook ,Twitter & Google + ,Youtube ” , and Email Alerts , so that you will get all the upcoming updates for you instantly
No comments:
Post a Comment